Home page

G2818A/G2818B

The product is widely used for testing various parameters of high-frequency electronic transformers, inductors, coils, capacitors, resistors, magnetic materials and other components

Category:

Precision LCR digital bridge

Keywords: electronic testing instruments

MESSAGE

Product Details

Introduction

GKT2818A/B precision LCZ tester is an impedance measuring instrument with high precision, high stability, fast test speed, wide test range and large data storage space. It uses an advanced 32-bit microprocessor and a 4.3-inch color display. , Humanized interface menu design, convenient and quick operation, can perform routine, comparison, sorting, scanning measurement, can save or read test data and related content in large capacity, provide a basis for users to control product quality and analyze product characteristics, and It greatly meets the different testing needs of users; at the same time, the instrument also provides Handler interface and RS-232C serial communication interface, which provides conditions for automatic measurement, remote control, and data transmission.

Performance characteristics

■ 4.3 inch color screen display,

■ Test frequency: 50Hz to 200KHz, arbitrarily set (only 2818A)

■ Test frequency: 50Hz to 200KHz, 37 fixed frequency points can be selected (2818B)

■ Test level 10mV ~ 2V, 10mV stepping (when the internal resistance is 10Ω, the highest setting voltage is 1V)

■ Basic accuracy 0.05%

■ High-speed and high-efficiency measurement: the fastest 32 times per second

■ Load correction: According to the specific sample and parameter instrument to calculate and correct, get the required test data.

■Comparator function: After setting one or more sets of range values of the product measurement parameters, the instrument can compare the obtained measurement value with the set value and judge whether it is a qualified product or a defective product.

■ Real-time recording of measurement results, with measurement date, product measurement data file name, statistics on the number of measurements in a day and other related information, the data will not be lost when the machine is turned on and off

■ File management function: 100 sets of product test data can be stored

■ Sorting function: to subdivide the product level, cooperate with the control mechanical sorting system to sort and classify the products.

■ V, I test signal level monitoring function

■ Up to 8 points of frequency or 8 points of voltage can be scanned and measured, and the measurement results can be displayed at the same time

■ Communication interface: RS232C/HANDLER

General specifications

temperature humidity		0 ° C - 40 ° C, 90% RH
Power requirements	Voltage	200-240V
	frequency	60Hz
Power consumption		≤60 VA
Dimensions (W×H×D)		300mm×120mm×360mm
weight		About 3.5kg

technical parameter

Measurement function
Measurement parameters	Ls-Q, Ls-Rs, Lp-Q, Lp-Rp, Cs-D, Cs-Rs, Cp-D, Cp-Rp, Z-deg (angle), Y- deg (angle), RX, GB ( Conductance-susceptance)
Basic accuracy	0.05%
Test speed	Fast speed: 32, medium speed: 9, slow speed: 4 (times/sec)
Equivalent Circuit	Series Parallel
Trigger method	Internal, manual, external
Correction function	Open/short circuit, full frequency clear, single point frequency clear
monitor	4.3 inch color screen
Memory	Internal 100 groups, external U disk multiple groups
Test signal
Test frequency	G2818A	50Hz – 200KHz, resolution: 10mHz
	G2818B	50Hz -200KHz, 37 common frequency points
Output impedance	10Ω, 30Ω, 100Ω
Test level	10mV ～ 2V, resolution: 10mV
Measurement display range
Z, R,X	0.01mΩ ～ 9999.99MΩ
Y, G, B	0.01nS～999.999S
C	0.00001pF ～ 9999.99mF
L	0.01nH～9999.99H
D	0.00001 ～ 9.99999
θ (Deg)	-179.9° – 179.9°
Q	0.00001 ～ 99999.9
Comparator and interface
Comparators	9 grades sorting
	PASS/FAIL
interface	RS232C / HANDLER

Ordering Information

G2818A precision LCR digital bridge

G2818B precision LCR digital bridge

Instrument accessories

Four-terminal test fixture

Four-terminal Kelvin test cable

Gold-plated short circuit board

Optional accessories

SMD component test fixture

SMD test clamp

GPIB interface board

Data acquisition software

Performance characteristics
4.3 inch color screen display,
Test frequency: 50Hz to 200KHz, any setting (2818A only)
Test frequency: 50Hz to 200KHz, with 37 fixed frequency points (2818B) available for selection
Test level 10mV~2V, 10mV step by step (when the internal resistance is 10 Ω, the highest set voltage is 1V)
Basic accuracy 0.05%
High speed and efficient measurement: up to 32 times/second
Load correction: Calculate and correct the required test data based on specific samples and parameter instruments.
Comparator function: After setting one or more range values of product measurement project parameters, the instrument can compare the obtained measurement values with the set values to determine whether it is a qualified or defective product.
Real time recording of measurement results, accompanied by relevant information such as measurement date, product measurement data file name, and statistics of the number of measurements per day, ensures that the on/off data is not lost
File management function: can store 100 sets of product testing data
Sorting function: subdivide the product into levels, and cooperate with the control mechanical sorting system to sort and classify the products.
V, I test signal level monitoring function
■ Can scan and measure up to 8 frequencies or 8 voltages, while displaying measurement results
Communication interface: RS232C/HANDLER

G1062A

G101

G2818A/G2818B

Message